Minelab SD2100v2 Manual de Instruções

Instruction Manual Page 14. Control Box4.1 Rear Panel ControlsPower SwitchThe Power switch controls the power supply from the battery to the controlbo

Page 2 The Minelab SD2100v24.2 Front Panel ControlsSearch SwitchGround Balance mode (Balance 1 and Balance 2)To get the best results from your SD2100v

Instruction Manual Page 15. OperationThe SD2100v2 does not have an external speaker. All sound is heardthrough the headphones, which plug into the hea

Page 2 The Minelab SD2100v25.2 Operating Instructions5.2.1 Detector SoundsThreshold: This is the background sound produced by the detector. Theloudnes

Instruction Manual Page 3Figure 5 - Ground Balancing5.2.5 Set the Tune ControlWith the SD2100v2 switched On and the Threshold control and Tone control

Page 4 The Minelab SD2100v2b) Adjust the Balance 1 control so that no variation in volume or pitch isheard as the coil is moved up and down. The great

Instruction Manual Page 5CAUTIONOnly use 6 volt batteries as recommended by Minelab.Never use a 12 volt battery as this will damage the detector. This

Page 6 The Minelab SD2100v2b) Plug the battery lead into the charger, then plug the mains charger intoa mains outlet. Switch the mains outlet on. Chec

Instruction Manual Page 77. Detecting Techniques7.1 SearchingThe SD2100v2 is a ‘motion’ detector, which means that it must be movingin relation to a t

Page 8 The Minelab SD2100v2Each sweep should overlap the area covered by the previous sweep. Thiswill ensure a full coverage of the searched area. Be

The Minelab SD2100v2INSTRUCTION MANUALMINELAB

Instruction Manual Page 97.3 Hints for Maximum Gold Recoverya) Keep the coil as close to the ground as possible.b) Listen very carefully. This is more

Page 10 The Minelab SD2100v27.5 PinpointingIn order to save time in the recovery of an object and to reduce the size ofthe hole required to extract it

Instruction Manual Page 117.6 Digging the TargetOnce you have established the location of the target it is necessary to diga small hole to recover it.

Page 12 The Minelab SD2100v2NOTE: Always refill the hole you have dug, and leave the area as youfound it.7.6.1 Digging Deep TargetsThe SD2100v2 has un

Instruction Manual Page 138. MaintenanceThe SD2100v2 is a high quality electronic instrument which is finelyengineered and housed in a durable contain

Page 14 The Minelab SD2100v29. TroubleshootingUse the following table to check for problems which you can diagnose:If you need to return your detector

Instruction Manual Page 1510. SpecificationNOTE: In the interest of product improvement, Minelab reserves the rightto make changes to this specificati

Page 16 The Minelab SD2100v211. WarrantyThere is a two-year parts and labour warranty on the SD2100v2 controlbox. Refer to your Product Warranty card

Instruction Manual Page 1712. AccessoriesFigure 9 - Coil Search Patterns12.1 Search CoilsThe SD2100v2 is supplied with the 11” Double ‘D’ as its stand

Page 18 The Minelab SD2100v2Each Monoloop coil consists of only one coil of wire and gives a detectionpattern similar to a concentric coil. Each Doubl

WARNINGTHIS DOCUMENT CONTAINSMINELAB ELECTRONICSLIMITED RIGHTS TECHNICAL DATA, ORRESTRICTED RIGHTS DATA, OR BOTH.© Minelab Electronics Pty LimitedThis

Instruction Manual Page 19

The Minelab SD2100v2Instruction ManualTable of Contents1. Introduction ...

Page 4 The Minelab SD2100v21. IntroductionThank you for purchasing the Minelab SD2100v2.You will find this detector to be one of the finest available

Instruction Manual Page 5Figure 1 - SD2100v2 List of Parts

Page 6 The Minelab SD2100v22. List of PartsThe SD2100v2 is packed in a single box containing the detector and an11” Double ‘D’ coil. The following par

Instruction Manual Page 73. Unpacking and Assemblya) Place the two armrest halves (7) on either side of the shaft assembly(6) and ensure that the bolt

Page 8 The Minelab SD2100v2j) Fit the battery (12) into the battery bag (13).k) Plug the headphones (17) into the socket in the cap of the battery.l)